Page 1 of 2

[SOLVED] When you start the installer, it automatically closes

Posted: Sun Jan 13, 2019 4:17 pm
by AndreLevou888
There was a problem during the installation of ArcoLinux (18.12.7). When you start the installer, it automatically closes. Rebooting does not help. Overwriting a bootable flash drive does not help.

Re: [OPEN] When you start the installer, it automatically closes

Posted: Sun Jan 13, 2019 7:38 pm
by erikdubois
copy/paste answer from youtube here

Code: Select all

it should not do that. It always stays open on all my arcolinux iso's.
When this happens during development, I start calamares via a terminal in debugging mode
calamares -d
Link youtube comment
https://www.youtube.com/watch?v=ZDMvY0x ... bpR4AaABAg

Re: [OPEN] When you start the installer, it automatically closes

Posted: Mon Jan 14, 2019 3:02 pm
by AndreLevou888
erikdubois wrote:
Sun Jan 13, 2019 7:38 pm
copy/paste answer from youtube here

Code: Select all

it should not do that. It always stays open on all my arcolinux iso's.
When this happens during development, I start calamares via a terminal in debugging mode
calamares -d
Link youtube comment
https://www.youtube.com/watch?v=ZDMvY0x ... bpR4AaABAg
Today I tried to connect to another provider, started the installer with the Internet connected, the installer started without failures and the installation was successful. So the problem is not in the hardware. This problem is somehow related to the provider.

Re: [OPEN] When you start the installer, it automatically closes

Posted: Mon Jan 14, 2019 5:02 pm
by erikdubois
So the internet connection that you have or not have

Re: [OPEN] When you start the installer, it automatically closes

Posted: Mon Jan 14, 2019 5:14 pm
by AndreLevou888
erikdubois wrote:
Mon Jan 14, 2019 5:02 pm
So the internet connection that you have or not have
The problem is not in this when the Internet is connected, the Calamares installer is closed and it is impossible to install the system. But if you turn off the Internet, the installer starts and the system is installed

Re: [OPEN] When you start the installer, it automatically closes

Posted: Tue Jan 15, 2019 8:10 am
by erikdubois
How do you turn of the internet?
What do you do exactly?
Might help others.

Re: [OPEN] When you start the installer, it automatically closes

Posted: Fri Jan 18, 2019 8:40 am
by AndreLevou888
erikdubois wrote:
Tue Jan 15, 2019 8:10 am
How do you turn of the internet?
What do you do exactly?
Might help others.
I disconnect the ethernet cabel from the laptop, launch calamares, and the installation proceeds normally. But if the ethernet cabel is connected and the Internet is connected, then after launching calamares it closes at the stage of choosing the language of the installer calamares

Re: [OPEN] When you start the installer, it automatically closes

Posted: Fri Jan 18, 2019 10:35 am
by erikdubois
I wonder if you get an ip adress if you connect the cable?
ifconfig will show one

Re: [OPEN] When you start the installer, it automatically closes

Posted: Fri Jan 18, 2019 1:15 pm
by AndreLevou888
erikdubois wrote:
Fri Jan 18, 2019 10:35 am
I wonder if you get an ip adress if you connect the cable?
ifconfig will show one
how do you explain? when I come to work with my laptop and plug in the cable, launch calamares, it starts up without any problems and the installation proceeds normally. Problems arise at home, I have another provider at home. calamares closes the installer language selection stage. Now I'm at work, I reinstalled the system on a laptop with the cable connected, the installation was excellent

Re: [OPEN] When you start the installer, it automatically closes

Posted: Fri Jan 18, 2019 1:18 pm
by AndreLevou888
erikdubois wrote:
Fri Jan 18, 2019 10:35 am
I wonder if you get an ip adress if you connect the cable?
ifconfig will show one
Yes, I get the ip-address when connecting the cable.
received data: ip-address, subnet mask, main gateway. such data gives me my provider